Totalizing Transmitter with Ethernet I/O for 4-20 mA | 0-1 mA or 0-10V Analog Proces Signals

The Laureate process signal input transmitter and totalizer accepts 0-1 mA, 4-20 mA or 0-10V signals from flow meters and other transducers, such as watt meters, to track rate or totalized rate.

With a Standard Main Board, the transmitter output can track rate (such as gallons per minute or watts) or totalized rate (such as gallons or kilowatt hours) whether the transducer output is linear or requires square root extraction (differential pressure flow transducers).
With an Extended Main Board, the transmitter can also perform custom curve linearization (provided by a curvilinear spline fit with up to 180 data points), display 1/ rate (such as the time it takes a conveyor to pass through an oven), and perform batch control for repetitive fill operations. Such applications typically make use of optional dual solid state relays, which are available as options. External reset of totals is provided by a special connector.

Signal Conditioner Board for Laureate Analog Input Flow Rate Meter and Analog Flow Totalizer

A signal conditioner board converts the full-scale 0-1 mA, 4-20 mA or 0-10 V analog signal to a frequency of 10 kHz to 110 kHz. This frequency is determined by measuring period over a selected gate time (from 10 ms to 200 s) and taking the inverse of period. At the lowest frequency of 10 kHz and the minimum gate time of 10 ms, the transmitter is capable of 25 updates per second. Scaling is done mathematically. Totals are calculated as the product of rate and time in seconds regardless of the selected gate time. Totals are stored in nonvolatile memory in case of power loss.

Standard features of Laureate LTE transmitters include:

Ethernet I/O, isolated. Supported protocols are Modbus RTU and ASCII (tunneled via Modbus TCP) and Laurel ASCII. The latter is simpler than the Modbus protocol and is recommended when all devices are Laureates. Note that RS232 or RS485 data I/O in lieu of Ethernet is provided by LT Series transmitters.
Dual solid state relays, isolated. Available for local alarm or control. Rated 120 mA at 130 Vac or 180 Vdc.
Universal 85-264 Vac power. Low-voltage 10-48 Vdc or 12-32 Vac power is optional.

Discovery and configuration of Laureate Ethernet Nodes is easily achieved with Laurel's Node Manager Software, and the discovered transmitters can then be programmed using Laurel's Instrument Setup Software. Both softwares run on a PC under MS Windows and can be downloaded from this website at no charge.

Laureate Ethernet network by Laurel Electronics

Laureate Ethernet & 4-20 mA Transmitter & Totalizer for 0-1 mA, 4-20 mA or 0-10V Process Signals

Analog Input	0-1 mA	4-20 mA	0-10 V
Input resistance	1.00 kΩ	50 Ω	1.01 MΩ
Max current or voltage	35 mA	70 mA	600 V
Input Resolution	6 digits
Span Tempco	±0.003% reading/°C
Zero Tempco	±0.003% FS/°C
Accuracy at 25°C	±0.01% FS ± 1 count
Read Rate	25/sec (typical)

Analog Output (standard)
Output Levels	4-20 mA and 0-10 Vdc (selectable)
Compliance, 4-20 mA	10V (0-500Ω load)
Compliance, 0-10V	2 mA (5 kΩ load)
Output Resolution	16 bits (65,536 steps)
Output Accuracy	0.02% of output span
Output Update Rate	25/sec
Output Isolation	250V rms working, 2.3 kV rms per 1 minute test
Ethernet Data I/O (standard)
Type	10/100 Base-T Ethernet per IEEE 802.3
Data Rates	300, 600, 1200, 2400, 4800, 9600, 19200 baud
Output Isolation	250V rms working, 2.3 kV rms per 1 min test
Serial Protocols	Modbus TCP, Modbus RTU, Modbus ASCII, Laurel ASCII
Modbus Compliance	Modbus over Serial Line Specification V1.0 (2002)
Digital Addresses	247 for Modbus, 31 for Laurel ASCII
Transducer Excitation Output (standard)
Jumper Selection 1	10V @ 60 mA, isolated to 50V from signal ground
Jumper Selection 2	5V @ 50 mA, isolated to 50V from signal ground
Jumper Selection 3	15V @ 60 mA, non-isolated
Dual Relay Output (standard)
Relay Type	Two solid state relays, SPST, normally open, Form A
Load Rating	120 mA at 140 Vac or 180 Vdc
Power Input
Standard Power	85-264 Vac or 90-300 Vdc
Low Power Option	10-48 Vdc or 12-32 Vac
Power Frequency	DC or 47-63 Hz
Power Isolation	250V rms working, 2.3 kV rms per 1 min test
Power Consumption	2W typical, 3W with max excitation output
Mechanical
Dimensions	129 x 104 x 22.5 mm case
Mounting	35 mm rail per DIN EN 50022
Electrical Connections	Plug-in screw-clamp connectors
Environmental
Operating Temperature	0°C to 55°C
Storage Temperature	-40°C to 85°C
Relative Humidity	95% at 40°C, non-condensing
Cooling Required	Mount transmitters with ventilation holes at top and bottom. Leave 6 mm (1/4") between transmitters, or force air with a fan.

Laureate Ethernet & 4-20 mA Transmitter & Totalizer for 0-1 mA, 4-20 mA or 0-10V Process Signals

Laureate Ethernet & 4-20 mA Transmitter & Totalizer for 0-1 mA, 4-20 mA or 0-10V Process Signals
Click on the radio buttons to build a model number with pricing as shown below. Prices are in US dollars and do not include shipping or duty charges (export sales). Please see our explanations and limitations applicable to pricing and online orders. Prices shown are in US Dollars and are Laurel's manufacturer's suggested retail price (MSRP) in the USA. Orders are processed manually, not directly by our shopping cart system. You don't have to supply credit card information when placing an online order.

North American Orders. Laurel does not sell factory-direct in the USA or Canada. Online sales orders are filled through distribution. During the ordering process, you will have the chance to select an authorized Laurel distributor, or you can ask Laurel to refer you to a distributor. The distributor will then contact you to quote shipping, tax and duty (where applicable), and arrange for payment.

International Orders. If your ship-to address indicates that you are outside of the USA or Canada and Laurel has a distributor in your country, we will forward your order to that distributor for follow-up. If Laurel does not have a distributor in your country, we will email you an order acknowledgment and a pro forma invoice which states the product price, shipping charges, and wire transfer information, which includes a $25 bank wire transfer fee.

Questions about your order? Please email your distributor or sales@laurels.com

Quantity
Transmitter Type		LTE 4-20 mA & Ethernet output transmitter	$388
Transmitter Type		LT 4-20 mA & RS232/RS485 output transmitter	$164
Main Board		6 Standard Main Board	$0
		8 Extended Main Board	$55
	With Standard Main Board: Rate, square root of rate, or totalized rate from differential pressure flow transducers with a DC output. With Extended Main Board: Above plus linearization of nonlinear inputs, batch operation, 1/rate (time).
Power		0 Isolated 85-264 Vac or 90-300 Vdc	$89
Power		1 Isolated 12-32 Vac or 10-48 Vdc	$89
Input Type	Voltage-to-Frequency Converter
		VF1 V-to-F Converter, 4-20 mA	$81
		VF2 V-to-F Converter, 0-1 mA	$81
		VF3 V-to-F Converter, 0-10V	$81
Add-on Options		-X Extended operating temperature option from -40°C to 70°C	$0

Configured model number	LTE60VF1
Configured price per model	$558
Quantity	1
Extended price	$558

Call (714) 434 6131 for Product Assistance

Panel Meters - Counters - Timers - Transmitters, 4-20 mA & Modbus - Ethernet - USB - RS485 - RS232

Menu

Ethernet & 4-20 mA Output Transmitter and Totalizer for 0-1 mA, 4-20 mA or 0-10V Analog Proces Signals

Scalable to flow rate or total flow from process signals. DIN Rail mounted, digitally programmable.

Features

For applications assistance, phone 714-434-6131 ext. 104, or email support@laurels.com

Shopping cart